The gas type of boilers controls fuel consumption, the intensity of water movement. Devices consist of microprocessors, pumps, programmers, which function normally only with sinusoidal voltage. Reliable stabilizer Bastion for a gas boiler meets the specifics of the domestic power line, provides high-quality power to all elements of the system.
Technical characteristics of the stabilizer Teplokom
Stabilization devices are available in the Teplocom and SKAT ST series. The Teploc range is equipped with a microprocessor, it has a wide input voltage range.
Relay devices have the following technical parameters:
- voltage equalization up to 220-240 V under the condition of a network fluctuation of 145-260 V;
- work in the temperature range from -10 to +40 degrees;
- output voltage form - pure sine;
- power rating - 400 VA;
- maximum power - from 500 to 1300 VA;
- moisture protection class IP-20;
- the ability to operate at 80% air humidity.
The fuse is available in a white plastic case, is a volatile device with protection against overloads, short circuits, and is equipped with a noise filtering system.
The principle of operation of stabilizers
The Teploc stabilizer is used to equalize the power supply of equipment with a total absorption power of up to 800 VA. Uninterruptible voltage sources are suitable for continuous fan blackouts, low mains voltage or overvoltage. Devices provide autonomy of a gas boiler in the event of a power outage.
The UPS aligns the output voltage in the range of 220 V, if an external 135-270 V is supplied. When these indicators are exceeded, an automatic shutdown is triggered. After the output power returns to the operating range, the device will turn on again.
Protective systems maintain stabilizers in the event of a line fault. They function autonomously. Also, the devices of the Bastion holding automatically turn off when overheating.
Information about the voltage at the input / output is displayed on the board.
UPS specifications
The relay stabilizer responds to voltage parameters and equalizes it to the desired limit. The device is necessary for the following reasons:
- in case of failure, an imported gas boiler that is not connected to an uninterruptible power supply will have to be replaced, which involves financial costs;
- with voltage fluctuations, the life of boiler equipment and pumps is reduced;
- sudden shutdown of the heating system will lead to further breakdowns of communications.
Teplocom stabilizer is a modern device with many functions.
Simplicity and ease of connection
Gas boilers are phase-dependent equipment, so the manufacturer's instructions are needed to connect the UPS. It indicates a phased work algorithm:
- Connect the power plug of the stabilizer to a 220 V power outlet.
- Wait until the “Network” indicator appears.
- After 5-10 minutes, the device will begin to work.
Once every 6 months you will need to wipe the dust, check the product’s performance and contact integrity.
The output power of Bastion equipment must not be less than the total power consumption of the boiler.
Miniature sizes
You can choose a voltage stabilizer of the Teplokom series for floor and wall gas boilers. Depending on the model, the width, depth and height parameters are different:
- ST 222/500 - 104х104х135 mm;
- ST 555 - 130x170x85 mm;
- ST 888 and ST 1515 - 169x210x101 mm;
- CT 400 and 600 Invertor - phase inverter, 242x170x98 mm;
- ST-1000 and ST-1500 - 305x171x128 mm;
- ST-1300 - 322x220x134 mm.
The devices are designed for voltages from 222 to 1515 VA, comply with GOST 14254-2015.
Protection against voltage fluctuations, lightning and power failures
Under normal voltage conditions, the transformer produces +/- 15 V oscillations. If there is 220 V in the network, the voltage immediately goes to the consumer, has a transformation ratio of 1. In the range of 205-235 V, the output voltage does not change. When racing, the following happens:
- less than 205 V - the secondary winding is activated with a coefficient of 1.75. The tap closes, the current goes to the output contacts;
- above 235 V - the secondary winding is activated, the transformation coefficient of which is 0.94. The voltage is equalized to 220 V.
The accident protection system is implemented:
- With the help of surge thresholds and current sagging at the output, the load is switched off in a few seconds. When parameters are normalized, the fuse voltage works again.
- Bypass - voltage is supplied bypassing the circuit; the fault can be eliminated without turning off the boiler.
If lightning strikes, a thermal protection system is applied - the UPS is not powered until the winding transformers have cooled down.
High overload limit
A large overload capacity ensures the use of uninterrupted power in conjunction with equipment characterized by a high inrush current. The device can be installed indoors, connected to wall and floor boilers with an open or closed combustion chamber.
Advantages and disadvantages
Relay stabilizers from Teplocom have several advantages:
- inexpensive price with a long service life;
- functioning at an input voltage of the range 140-290 V;
- response speed from 100 to 200 V / s;
- small dimensions and light weight;
- connection to equipment with zero load;
- microprocessor type of control, providing switching of the windings when crossing through zero;
- minimum wear of contacts;
- the presence of several degrees of protection - from power surges, emergency situations on the line, high-frequency interference, weather factors.
The disadvantages of relay modifications include service life depending on the quality of the assembly, the inability to use for lighting systems. An uninterruptible power supply can click loudly at the moment of protection operation.
Terms of Use
When operating Teplocom stabilization devices, a 2-5 year warranty must be considered, subject to the requirements. The manufacturer notes the basic requirements for operation:
- The power of the equipment is selected according to the parameters of the mains voltage.
- Installation is possible only in a dry room, without current dust and fumes of household chemicals.
- The stabilizer works in an open area, is not placed in a pedestal, niche or cabinet.
- The operating temperature of the device for indoor use should be in the range from +5 to -40 degrees.
The entire line of the brand is connected to the power grid using a plug. A socket is used to connect to the boiler.
The nuances of choosing stabilizers Teplokom
When buying a device, you need to consider the quality of the output current, power, response speed, voltage indicators at the input and output. A sine wave for a quality signal should be almost perfect. The Teplocom range is suitable for all heating boilers, since it does not change the direction of the current in the network. The selection of the device is carried out taking into account such factors:
- Electric power should be 30% more than the boiler power.
- The presence of circulating sediment. The power is calculated using the formula, Vtot = 1.3 x (V1 + V2 ∙ 3), where: V1 is the boiler power, VA. V2 - power of the circulation pump, VA. 3 - coefficient of accounting for voltage fluctuations at the time of pump start-up, 1.3 - coefficient of power reserve.
- Response time. For gas boilers, fuses with a shorter response time and a higher voltage equalization speed are suitable.
- Input voltage parameters. Devices with a minimum input range are not suitable for low voltage networks.
- Deviation from the output current. The range for a 220 V network should be minimal.
The simplest heating equipment can withstand a deviation of up to 10%, models with automation - up to 5%.
Teploc stabilizers are suitable for imported and Russian gas boilers. The manufacturer produces devices of the budget price range, which are distinguished by quality and an extensive model range.
